Makefile.am
2.6 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
TXT3 = \
modbus_close.txt \
modbus_connect.txt \
modbus_flush.txt \
modbus_free.txt \
modbus_get_byte_from_bits.txt \
modbus_get_byte_timeout.txt \
modbus_get_float.txt \
modbus_get_float_abcd.txt \
modbus_get_float_badc.txt \
modbus_get_float_cdab.txt \
modbus_get_float_dcba.txt \
modbus_get_header_length.txt \
modbus_get_response_timeout.txt \
modbus_get_slave.txt \
modbus_get_socket.txt \
modbus_mapping_free.txt \
modbus_mapping_new.txt \
modbus_mapping_new_start_address.txt \
modbus_mask_write_register.txt \
modbus_new_rtu.txt \
modbus_new_tcp_pi.txt \
modbus_new_tcp.txt \
modbus_read_bits.txt \
modbus_read_input_bits.txt \
modbus_read_input_registers.txt \
modbus_read_registers.txt \
modbus_receive_confirmation.txt \
modbus_receive.txt \
modbus_reply_exception.txt \
modbus_reply.txt \
modbus_report_slave_id.txt \
modbus_rtu_get_serial_mode.txt \
modbus_rtu_set_serial_mode.txt \
modbus_rtu_get_rts.txt \
modbus_rtu_set_rts.txt \
modbus_rtu_set_custom_rts.txt \
modbus_rtu_get_rts_delay.txt \
modbus_rtu_set_rts_delay.txt \
modbus_send_raw_request.txt \
modbus_set_bits_from_bytes.txt \
modbus_set_bits_from_byte.txt \
modbus_set_byte_timeout.txt \
modbus_set_debug.txt \
modbus_set_error_recovery.txt \
modbus_set_float.txt \
modbus_set_float_abcd.txt \
modbus_set_float_badc.txt \
modbus_set_float_cdab.txt \
modbus_set_float_dcba.txt \
modbus_set_response_timeout.txt \
modbus_set_slave.txt \
modbus_set_socket.txt \
modbus_strerror.txt \
modbus_tcp_accept.txt \
modbus_tcp_pi_accept.txt \
modbus_tcp_listen.txt \
modbus_tcp_pi_listen.txt \
modbus_write_and_read_registers.txt \
modbus_write_bits.txt \
modbus_write_bit.txt \
modbus_write_registers.txt \
modbus_write_register.txt
TXT7 = libmodbus.txt
EXTRA_DIST = asciidoc.conf $(TXT3) $(TXT7)
MAN3 = $(TXT3:%.txt=%.3)
MAN7 = $(TXT7:%.txt=%.7)
if BUILD_DOC
man3_MANS = $(MAN3)
man7_MANS = $(MAN7)
endif
HTML = $(TXT3:%.txt=%.html) $(TXT7:%.txt=%.html)
htmldoc: $(HTML)
.txt.html:
asciidoc -d manpage -b xhtml11 -f asciidoc.conf -alibmodbus_version=@LIBMODBUS_VERSION@ $<
.txt.3 .txt.7:
a2x --doctype manpage --format manpage -alibmodbus_version=@LIBMODBUS_VERSION@ $<
CLEANFILES = *.3 *.7 *.html